PNEUMATIC & ELECTROPNEUMATIC TRAINING SET

The Pneumatic and electro pneumatic Training Set should be produced for teaching three main subject: Pneumatic,
Electropneumatic and PLC. The training set shall contain suitable components for basic level and advanced level
applications.

All pneumatic and electropneumatic components should have plastic holder for to mount the aluminium panel. The application book should be given with set.

TRAINING SUBJECTS
•    Application of pneumatic & electropneumatic circuits
•    Application of  single and double cylinders
•    Pressure adjusting regulators and pressure sequence valves
•    Application of Mechanical,Air piloted, Logic control valves
•    Circuit configuration with relays and logic electric moduls
•    Application of PLC and Electropneumatic
•    Cascad circuits applications
•    Proportional pneumatic applications
•    Using of sensors on electropneumatic circuits
•    DC and step motor applications
•    Using of signal lamps and buttons on circuits
•    Simulation of program
•    Application of digital inputs/outputs on PLC
•    Application of digital inputs/outputs on PLC
•    Setup and piping of preesurised air systems
•    Study on repairing of pneumatic circuits
•    Study on pneumatic documents

1.    LAB DESK
•    Lockable wheeled, aluminium structure, laminat covered table
•    Single (or double sided) side used  lab desk
•    There shall be part on the top of desk for control panels.
•    Worktable min. 1200x800 Laminate Coated, One Sided (or double sided)
•    Triple Drawer Group
•    T-Channel Aluminium Plate min.1000x700 (2 Pcs if double sided)

2.    BASIC PNEUMATIC
The basic pneumatic set contains basic components for your applications.All components have plastic holder.With
transparent cylinder you can study on mechanical structure.The component list is on bellow.
TECHNICAL SPECIFICATION OF COMPONENTS
•    0-10 bar operation pressure
•    4 mm air connection
•    Easy connection between components
•    Plastic holder with components
•    Min. 280 lt/min flow rate
•    Actuation force 16 N
•    New technology plastic holder,

SYSTEM SHOULD BE INCLUDE FOLLOWING COMPONENTS
•    Min. 2 Pcs 3/2-Way Valve With Pushbutton, Normally Closed
•    Min. 1 Pcs 3/2-Way Valve With Pushbutton, Normally Open
•    Min. 1 Pcs 3/2-Way Valve With Emergency Switch, N. Open
•    Min. 1 Pcs 5/2-Way Valve With Selector Switch
•    Min. 1 Pcs 3/2-Way Roller Lever Valve,Normally Close
•    Min. 1 Pcs 3/2-Way Single Acting Pneumatic Valve, N.Close
•    Min. 1 Pcs 5/2 Way Single Acting Pneumatic Valve
•    Min. 1 Pcs 5/2 Way Double Acting Pneumatic Valve
•    Min. 1 Pcs Filter Regulator (With Manometer)
•    Min. 1 Pcs Regulator (With Manometer)
•    Min. 1 Pcs Manometer
•    Min. 1 Pcs Air Distribution Block (8's)
•    Min. 1 Pcs OR Valve
•    Min. 1 Pcs AND Valve
•    Min. 1 Pcs 3/2 Time Delay Valve, Normally Close
•    Min. 1 Pcs Quick Exhaust Valve
•    Min. 2 Pcs One Way Flow Control Valve For Cylinder Use
•    Min. 1 Pcs Cylinders Single Acting Spring Ahead (20x50)
•    Min. 1 Pcs Double Acting Cylinder (20x100)
•    Min. 1 Pcs Double Acting and Shaft Transparent Cyl. (20x100)
•    Polyurethane Hose 4 mm min. 15 mt.

3.    ADVANCED PNEUMATIC

SYSTEM SHOULD BE INCLUDE FOLLOWING COMPONENTS
•    Min. 1 Pcs 3/2 Way Valve Lever Switch, Normally Close
•    Min. 1 Pcs 5/2 Way Valve Lever Switch
•    Min. 1 Pcs 5/3 Way Hand Lever Valve Mid Pos. Closed
•    Min. 1 Pcs 3/2 Wayroller Lever Valve Single Side Actuated N.C.
•    Min. 2 Pcs 5/2 Way Double Acting Pneumatic Valve
•    Min. 1 Pcs Pneumatic Counter
•    Min. 1 Pcs Pneumatic Lamp (Line Type)
•    Min. 1 Pcs Vacuum Generator
•    Min. 1 Pcs Suction Cup
•    Min. 1 Pcs Double Acting Cylinder With Cushion (20x100)

4.    ELEKTROPNEUMATIC

SYSTEM SHOULD BE INCLUDE FOLLOWING COMPONENTS
•    Min. 2 Pcs 3/2 Way Single Acting Solenoid Valve N.Close
•    Min. 2 Pcs 5/2 Way Single Acting Solenoid Valve
•    Min. 1 Pcs 5/2 Way Double Acting Solenoıd Valve
•    Min. 1 Pcs 5/3 Way Mid Position Closed Solenoid Valve
•    Min. 1 Pcs Single Acting Cylinder With Magnet (20x50)
•    Min. 1 Pcs Double Acting Cylinder With Magnet (20x100)
•    Min. 1 Pcs Double Acting Transparent C. With Magnet (20x100)
•    Min. 1 Pcs Pressure Switch N.Open/N.Close
•    Min. 1 Pcs Inductive Sensor
•    Min. 1 Pcs Capacitive Sensor
•    Min. 1 Pcs Optical Sensor
•    Min. 2 Pcs Proximity Sensor For Cylinder Use
•    Min. 1 Pcs Digital Pressure Sensor
•    Min. 1 Pcs Limit Switch Roller
•    Cable Set

5.    CONTROL PANELS
This panels shoudl be designed for electropneumatic applications. All inputs and outputs should be with 4 mm sockets. Each control panel shoudl have circuit diagram on his board. Easy used on lab desk

SYSTEM SHOULD BE INCLUDE FOLLOWING COMPONENTS
•    Power Supply(24V DC, Short Circuit and Overcurrent Protection, Emergency Stop, On-Off Switch, 4 mm plug)
•    Group Load (DC Motor, Stepper Motor, a Lamp, Buzzer)
•    Relay Group (4 relays. Relay Discrete of a 3 x NO / NC Contact Output)
•    Counter-Timer (Time Relay Contact Output For Analog, Digital Counter Output Contacts)
•    Light Switch Panel (2 pcs a permanent, non permanent 2)
•    Operator Panel (KP 300, TEN button)
•    PLC Module (8/8 digital inputs/outputs, input simulation switches, Programming CD