PNEUMATIC & ELECTROPNEUMATIC TRAINING SET
The Hydraulic and ElectroHydraulıc Training Set should be produced for teaching three main subject: Hydraulic, Electrohydraulic and PLC. The training set shall contain suitable components for basic level and advanced level applications.
All hydraulic and electrohydraulic components should have plastic holder for to mount the Aluminium panel. The application book should given with set.
TRAINING SUBJECTS
• Application of hydraulic&electrohydraulic circuits
• Set up the power unit
• Application on electrical and mechanical valves
• Application on speed control valves
• Pressure adjusting regulators and pressure sequence valves
• Application on Gas pressurised accumulator
• Proportional valves, Solenoid operated valves,
• Circuit configuration with relays and logic electric moduls
• Application of PLC and electrohydraulic
• Using of sensors on electrohydraulic circuits
• DC, Step motor and Hydraulic Engine applications
• Using of signal lamps and buttons on circuits
• Simulation of program
• Application of digital inputs/outputs on PLC
• Application of digital inputs/outputs on PLC
• Study on repairing of hydraulic circuits
1. LAB DESK
• Lockable wheeled, aluminium structure, laminat covered table
• Single (or double sided) side used lab desk
• There shall be part on the top of desk for control panels.
• Worktable min. 1200x800 Laminate Coated, One Sided
• Triple Drawer Group
• T-Channel Aluminium Plate min.1000x700 (2 Pcs if double sided)
• Min. 1 Pcs Oil Collecting Tray (2 Pcs if double sided)
• Hydraulic Power Units (Pressure Safety Valve, 3 l/min Flow Rate, Max Pressure 120 Bar, 0.37 kW Electric Motor 220V AC, 20 L. Tank Capacity, Start/Stop in the sand box
2. HYDRAULIC
The set shall contain hydraulic components for applications.All components should have plastic holder.
SYSTEM SHOULD BE INCLUDE FOLLOWING COMPONENTS
• Min. 1 Pcs Pressure Sequence Valve
• Min. 1 Pcs 3 Way Pressure Reducing Valve
• Min. 1 Pcs Pressure Compensators
• Min. 1 Pcs 4/2 way manual valve
• Min. 1 Pcs 4/3 Way Manual Valve Mid Position Close
• Min. 1 Pcs 4/3 Way Manual Valve "Y" Center
• Min. 1 Pcs 4/3 Way Manual Valve "H" Center
• Min. 1 Pcs 4/3 Way Manual Valve Mid Position Open
• Min. 1 Pcs Shut-Off Valve
• Min. 1 Pcs Diaphragm Accumulator With Safety Block
• Min. 1 Pcs OR Valve
• Min. 1 Pcs Non Return Valve 0,5 Bar
• Min. 1 Pcs Two Way Flow Control Valve
• Min. 1 Pcs One Way Flow Control Valve
• Min. 2 Pcs Double Acting Cylinder (20x200)
• Min. 1 Pcs Hydromotor
• Min. 3 Pcs T Fitting Witk Quick Couplings
• Min. 1 Pcs Manometer
• Min. 1 Pcs Distributor Block, P,T
• Min. 18 Pcs Hose with Quick Coupling(6x50,6x100,6x150,Holder)
• Min. 1 Pcs Pressure Filter
3. ELECTROHYDRAULIC
The set shall contain electrohydraulic components for applications. All components should have plastic holder.
SYSTEM SHOULD BE INCLUDE FOLLOWING COMPONENTS
• Min. 1 Pcs 4/2 Way Solenoid Valve
• Min. 1 Pcs 4/3 Way Solenoıd Valve Mid Position Closed
• Min. 1 Pcs 4/3 Way Solenoid Valve "Y" Center
• Min. 1 Pcs 4/3 way solenoid valve "H" center
• Min. 1 Pcs 4/3 Way Solenoid Valve Mid Position Open
• Min. 2 Pcs Double Acting Cylinder 20x200 with Magnetic Sensor
• Min. 1 Pcs Pressure Relief Valve (Electrical)
• Min. 1 Pcs Pressure Switch
• Min. 1 Pcs Pressure Transducer
• Min. 1 Pcs Inductive Sensor Normally Open
• Min. 1 Pcs Capacitive Sensor Normally Open
• Min. 1 Pcs Optical Sensor Normally Open
• Min. 1 Pcs Roller Limit Switch Normally Open
4. CONTROL PANELS
This panels shoudl be designed for electropneumatic applications. All inputs and outputs should be with 4 mm sockets. Each control panel shoudl have circuit diagram on his board. Easy used on lab desk
SYSTEM SHOULD BE INCLUDE FOLLOWING COMPONENTS
• Power Supply(24V DC, Short Circuit and Overcurrent Protection, Emergency Stop, On-Off Switch, 4 mm plug)
• Group Load (DC Motor, Stepper Motor, a Lamp, Buzzer)
• Relay Group (4 relays. Relay Discrete of a 3 x NO / NC Contact Output)
• Counter-Timer (Time Relay Contact Output For Analog, Digital Counter Output Contacts)
• Light Switch Panel (2 pcs a permanent, non permanent 2)
• Operator Panel (Siemens TD200, Text display, nine button, the PLC connection)
• PLC Module (CPU 222) (8/6 digital inputs/outputs, input simulation switches, PPI Cable, Programming CD